TOFFEE项目
文档更新影片研究下载赞助商联系


RESEARCH 》 Off-Grid Solar Power System for Raspberry Pi

Off-Grid Solar Power System for Raspberry Pi

When you choose to use your Raspberry Pi device as your IoT based remote weather station or if you are building Linux kernel (like kernel compilation) within the same, you need a good uninterrupted power source (UPS). But if you are using it on site or in some research camping location you can choose to power your Raspberry Pi device with your custom off-grid solar power source.

You can choose to use a small 12 Volt 10-14watt solar panel like this. This is quite ideal for charging a standard 12 volt - 7.2Ah Lead-acid battery. And while charging it will have sufficient to current left to power your Raspberry Pi device.
Off-Grid Solar Power System for Raspberry Pi

You can charge your battery via a solar panel to battery charge controller as shown below. The voltage output of these charge controllers should be around 13.5 to 14.5 volts which is ideal to charge your 12v battery. This will also ensure that the battery is never overcharged and will trickle charge if the battery is fully charged. The solar panel which is rated 12volts will generate around 18 to 19 volts in peak sunlight. So it is never a good idea to control the solar panel directly to a battery without a charge controller.
Off-Grid Solar Power System for Raspberry Pi - solar battery charge controller

Here is my compact low power UPS. This is a general purpose CFL/LED UPS with few power sockets (in this case 220volts AC). The advantage of this UPS is that it is meant to be used continuously 24/7 unlike high-power standard 600VA UPS (such as your APC UPS). The high-power UPS beeps if there is a power failure and a micro-controller restricts charging the battery via external charging units. This low power UPS delivers 45-50VA power output which is ideal to power Raspberry Pi, a small LED monitor, and charge your mobile devices. It dissipates less heat which is what we need in this case. It case without battery installed. So I need to purchase a standard 12volt sealed maintenance free (SMF) 7.2Ah lead-acid battery and installed the same within it.

Sometimes these are also called as Mini-UPS, and sometimes as LED UPS. These are mainly meant to serve as emergency power-backup (as an emergency lamp) and besides you can also charge your Mobile Phones, Tablets, etc. However they are not suited for a Laptop. Since a laptop charger typically consume 95-110W AC when it charges the laptop. And in normal operating mode, it consumes around 35-50W AC. And for the same reason it is well suited for powering your Raspberry Pi device. If you have a standard 120/240v AC to 5v 2Amp DC power adapter you can use with this UPS to power your Raspberry Pi.

The truth is sometimes it is better to call this device as a mini Inverter than a UPS.
Off-Grid Solar Power System for Raspberry Pi - low power CFL or LED UPS

You can see various power outlets/sockets of the UPS along with an 1-Amp protection fuse.
Off-Grid Solar Power System for Raspberry Pi - low power CFL or LED UPS power socket

Backside of the UPS as you can see in the picture below. I hacked the same and connected its battery terminals internally to this power socket. Which this I can directly bypass the UPS, charge the battery when in need via my solar panel or draw power 12volts directly from the battery terminals. It is quite unsafe to use this socket since you can connect reverse polarity, so alternatively you can use safe Molex 12v 5v computer power connectors or a standard DC power jack for this purpose.
Off-Grid Solar Power System for Raspberry Pi - low power CFL or LED UPS battery socket

So with this setup you can power-up your Raspberry Pi via standard 110v/220v 5volts 2amp power-supply. Or you can use directly 12volts to 5volts 2amp Car USB power adapter. Alternatively you can build a 5volt 2Amp Raspberry Pi power supply adapter with LM78S05 voltage regulator. You can find the circuit and instructions HERE.

WARNING: Never use any untested car 5v USB power supply since it may not deliver the required 2Amp current. Since these adapters are mainly meant for charging your low-power mobile phones.

WARNING: Never build a 5volt power supply adapter with LM7805 voltage regulator, since it delivers just 1Amp maximum current.

Just for thought: In Bangalore (India), the government insists home owners to install these Solar Water Heaters on their terrace. They provide subsidy and moreover these days it is becoming a mandatory requirement for new home owners before they apply for new home utility power connection(s) to their home(s).
Bangalore India - Solar Water Heaters installed on a terrace

These Solar water heating units are incredibly efficient as they convert the solar power directly into heat. They contain heat exchangers inside these large heat insulated reservoirs where the heated water is stored or later use in the home. Unlike a solar based electricity generation process, a solar based heating system is lot more efficient. The amount of power loss during the process is way too less. And the heat (energy) stored in this system is efficient than the way energy stored in a battery in the form of chemical energy. Which is why we need better power (electricity) storage systems such as super-capacitors and so on.
Bangalore India - Solar Water Heaters installed on a terrace

Here is my live detailed video-log of the same:

Power Consumption of Raspberry Pi: Raspberry Pi consumes way too less power. However it is important to understand the power consumption of the same with respect to the load on the device, such as casual browsing, kernel compilation, etc. Hence I connected a Raspberry Pi device via my Kill-a-watt kind of kilowatt power meter as shown below and measured its power consumption parameters. This I did along with my other lab equipment and published the same as a complete detailed article HERE.
Power consumption of my Home Lab devices for research - Raspberry Pi

💎 TOFFEE-MOCHA new bootable ISO: Download
💎 TOFFEE Data-Center Big picture and Overview: Download PDF


推荐主题:

My Lab HDD and SSD logs for research ↗
Saturday' 13-Mar-2021

TOFFEE (and TOFFEE-DataCenter) optimized Mobile Wireless Backhaul Networks ↗
Saturday' 13-Mar-2021
TOFFEE can be used to optimize expensive Wireless backhaul network infrastructure. TOFFEE can be deployed over existing slow or often outdated old backhaul networks too. This will leverage mobile ISPs and network service providers to reduce their bulk IT CapEx and OpEx Costs.

Timelapse Screen Capture of TOFFEE-DataCenter Network Acceleration - with new RRDtool graph support ↗
Saturday' 13-Mar-2021
Timelapse Screen Capture of TOFFEE-DataCenter Network Acceleration - with new RRDtool graph support

TOFFEE-Butterscotch Bandwidth saver software development - Update: 17-Nov-2016 ↗
Saturday' 13-Mar-2021
Here is my second software development update of TOFFEE-Butterscotch. In the previous update (28-Oct-2016) I discussed about the Alerts, etc. Whereas in my first TOFFEE-Butterscotch news update I have introduced about TOFFEE-Butterscotch research, project specifications, use-cases, etc.

Demo TOFFEE-DataCenter WAN Optimization VM Test Setup ↗
Saturday' 13-Mar-2021

TOFFEE-Mocha Documentation :: TOFFEE-Mocha-1.0.32-1-x86_64 and TOFFEE-Mocha-1.0.32-1-i386 ↗
Saturday' 13-Mar-2021



Internet optimization through TOFFEE-DataCenter WAN Optimization Demo ↗
Saturday' 13-Mar-2021
Internet optimization through TOFFEE-DataCenter WAN Optimization Demo

Timelapse Screen Capture of TOFFEE-DataCenter Network Acceleration - with new RRDtool graph support ↗
Saturday' 13-Mar-2021
Timelapse Screen Capture of TOFFEE-DataCenter Network Acceleration - with new RRDtool graph support

Demo TOFFEE-DataCenter WAN Optimization packaging feature ↗
Saturday' 13-Mar-2021

TOFFEE-Mocha WAN Emulation software development - Update: 15-July-2016 ↗
Saturday' 13-Mar-2021
Today I completed doing all the changes which are meant for the new upcoming TOFFEE-Mocha release. I have increased the resolution and the range of all factor variables. Instead 1 to 10 range now they have a range of 1 to 30. Unlike before the value 1 means it is lot more intense (or in some cases less intense) and the uppermost value 30 means lot less intense (or in some cases lot intense).



Featured Educational Video:
在YouTube上观看 - [434//1] 0x1d3 Who gets Laid off (or Fired) during a recession ? #TheLinuxChannel #KiranKankipati ↗

Demo TOFFEE-DataCenter WAN Optimization packaging feature ↗
Saturday' 13-Mar-2021

My Lab HDD and SSD logs for research ↗
Saturday' 13-Mar-2021

Building my own CDN - Google PageSpeed Insights - Update: 22-Jul-2016 ↗
Saturday' 13-Mar-2021
Ever since after I launched my new The TOFFEE Project website on 1-May'2016, I can see there is a steep increase in traffic. Soon after the launch when I monitored its Alexa rankings it was reporting about 12 Million or so. But once it is getting more and more traffic the Alexa rankings shot up and now currently it shows around 2 Million (as on 22-July-2016). Alexa is an excellent tool to monitor your overall website global ranking and indirectly its performance. Unlike Google Analytics which is bound one or other way into Google's SEO. Alexa gives you a second opinion about your website's growth.

TOFFEE-Mocha WAN Emulation software development - Update: 18-June-2016 ↗
Saturday' 13-Mar-2021
In the previous update (17-Jun-2016) I discussed about the upcoming new Random Packet drop feature along with other completed features. Now I completed the entire TOFFEE-Mocha Random packet drop feature. I completed all the kernel components and the UI support of the same. And to make GUI settings more organized I split the earlier Basic-Settings page into two separate pages namely: Packet Drop and Packet Delay. So this way it is simple to understand settings according to their functionality.




Demo TOFFEE-DataCenter WAN Optimization packaging feature ↗
Saturday' 13-Mar-2021



Research :: Optimization of network data (WAN Optimization) at various levels:
Network File level network data WAN Optimization


Learn Linux Systems Software and Kernel Programming:
Linux, Kernel, Networking and Systems-Software online classes [CDN]


Hardware Compression and Decompression Accelerator Cards:
TOFFEE Architecture with Compression and Decompression Accelerator Card [CDN]


TOFFEE-DataCenter on a Dell Server - Intel Xeon E5645 CPU:
TOFFEE-DataCenter screenshots on a Dual CPU - Intel(R) Xeon(R) CPU E5645 @ 2.40GHz - Dell Server