DOCUMENTATION 》 Setting up a WAN Emulator within VirtualBox

Raspberry Pi is often used as a single board computer for applications such as IoT, hobby projects, DIY, education aid, research and prototyping device. But apart from these applications Raspberry Pi can be used for real-world applications such as in making a full-fledged networking devices. Raspberry Pi is a single board ARM based hardware which is why it is also classified as ARM based SoC. Since it is ARM based it is highly efficient, tiny form-factor and lower in power consumption with moderate computational power. This will allow it to work several hours on emergency battery backup power supply such as low-cost domestic UPS and or some renewable energy source, which is a prerequisite for a typical networking device.

Download TOFFEE-DATACENTER-1.3.25-1-portable.tar.xz via Google Drive share: platform independent (portable) source: TOFFEE-DATACENTER-1.2.2-1-portable.tar.xz * Alternatively download from SOURCEFORGE project site. * Here are the TOFFEE-DataCenter supported features. * To know more about the project kindly refer TOFFEE-Datacenter Documentation, News and Updates

Assume you have two sites (such as Site-A and Site-B) connected via slow/critical WAN link as shown below. You can optimize this link by saving the bandwidth as well possibly improve the speed. However, the WAN speed can be optimized only if the WAN link speeds are below that of the processing latency of your TOFFEE installed hardware. Assume your WAN link is 12Mbps, and assume the maximum WAN optimization speed/capacity of Raspberry Pi is 20Mbps, then your link will get speed optimization too. And in another case, assume your WAN link is 50Mbps, then using the Raspberry Pi as WAN Optimization device will actually increase the latency (i.e slows the WAN link). But in all the cases the bandwidth savings should be the same irrespective of the WAN link speed. In other words, if you want to cut down the WAN link costs via this WAN Optimization set up, you can always get it since it reduces the overall bandwidth in almost all the cases (including encrypted and pre-compressed data).

TOFFEE/TOFFEE-DataCenter can be used to optimize Ad-Hoc Mobile Wireless Mesh-Networks. To learn more about the same here are some references: B.A.T.M.A.N. - https://en.wikipedia.org/wiki/B.A.T.M.A.N. Mobile ad hoc network (MANET) - https://en.wikipedia.org/wiki/Mobile_ad_hoc_network Wireless ad hoc network (WANET) - https://en.wikipedia.org/wiki/Wireless_ad_hoc_network open-mesh.org (Open Mesh) Wiki - https://www.open-mesh.org/projects/open-mesh/wiki

Today I refined the first page consolidated report graphs. TOFFEE-Mocha (unlike TOFFEE) is a WAN Emulator, so the graphs are supposed to highlight this purpose and should display the overall network activity. Unlike TOFFEE, the TOFFEE-Mocha report should contain in general what is received versus what is sent across the wire. In case if the packet drop feature is enabled, you should see few missing bytes and packets. Similarly in future I may support packet duplication feature, in that case you may see more packets/bytes sent versus the packets/bytes actually received.

Timelapse Screen Capture of TOFFEE-DataCenter Network Acceleration - with new RRDtool graph support

TrueBench is an unique open-source benchmarking system in which the core system performance and efficiency parameters are measured at extreme high resolution in the order of several million/billion µ-seconds for a given specific task. TrueBench is a part of The TOFFEE Project research. With TrueBench Raspberry Pi 3, Raspberry Pi 2B and Raspberry Pi 2 are benchmarked and you can do a comparative analysis with standard mainstream x86 devices.

I started working on the new TOFFEE project (which is the fork of my earlier TrafficSqueezer open-source project) starting from 1st January 2016 onwards. Ever since I was busy in research and altering certain old features so that it is more minimal than TrafficSqueezer, a more focused agenda, deliver refined code and a broader vision. I have lined up more things to follow in the upcoming months. I want to focus about all aspects of WAN communication technologies not just on core WAN Optimization research and technology.

PiPG is a powerful and yet simple Raspberry Pi Network Packet Generator. With PiPG you can now fabricate custom network packets and send via any Network Interface. Supports all kinds of standard Network Ports (Linux Kernel driver generated) such as Physical Network Interface ports, and an array of virtual ports such as loopback, tun/tap, bridge, etc. indispensable tool for: Network Debugging, Testing and Performance analysis Network Administrators Students Network R&D Protocol Analysis and Study Network Software Development Compliance Testing Ethical Hackers you can generate the following test traffic: L2-Bridging/Slow protocols: STP, LACP, OAM, LLDP, EAP, etc Routing protocols: RIPv1, RIPv2, IGMPv1, IGMPv2, OSPF, IS-IS, EIGRP, HSRP, VRRP, etc Proprietary protocols: CISCO, etc Generic: IPv4 TCP/UDP, etc Malformed random packets

Here are some of the screenshots of the new upcoming TOFFEE WAN Optimization release and live demo.

TOFFEE-Butterscotch yet another variant of TOFFEE can be used to save and optimize your Home/SOHO Internet/WAN bandwidth. Unlike TOFFEE (and TOFFEE-DataCenter) TOFFEE-Butterscotch is a non peer-to-peer (and asymmetric) network optimization solution. This makes TOFFEE-Butterscotch an ideal tool for all Home and SOHO users.